Download the Gleam Team app on the App Store
All articles

How to Clean Glass Block Basement Windows

By Gleam Team5 min read

How to clean glass block basement windows without a squeegee, why the texture holds grime, and why clean block looks brighter but never clear.

To clean glass block windows, put the squeegee away and pick up a soft brush. The texture is the whole problem. Every ripple in the face of a block is a low spot that holds grime, and a flat cloth or a rubber blade only ever touches the high spots. Warm water, a few drops of dish soap and a brush that reaches into the pattern will do more than an hour of wiping.

Why glass block does not wipe clean like a flat pane

A normal pane is smooth, so anything you drag across it touches all of it. Glass block is molded with a ripple, a wave or a fine grid pressed into one face and usually both. Dirt settles into the bottom of that pattern and sits there while your cloth slides across the top. That is why a block window can look worse after a wipe than before it.

Then there are the joints. Glass block is set in mortar like brick, so every block is framed by four narrow lines of rough grey cement that hold grit and dust the way a sidewalk does. A house full of flat glass has frames and sills to detail. A block window is mostly joint.

Where the grime on a basement block comes from

  • Cobwebs in the recess. A block window set back into a foundation wall is a sheltered corner, and sheltered corners are exactly where webs go. There is more on that in the piece on spider webs around windows.
  • Window well debris. Plenty of basement block sits in a well under a layer of leaves and silt, which has to come out first. That is its own job, covered in cleaning out window wells.
  • A white chalky bloom on the mortar. Salts work their way out of masonry over the years and dry on the surface. It is not dirt and it will not scrub off like dirt.
  • Basement air on the inside. Furnace dust, dryer lint and workshop grit land on the inside face, and the texture gives all of it something to hold.

How to clean glass block, step by step

Brush the loose material off dry first. A soft bristle brush, the kind sold for washing a car, is the right shape for this and will not mark the glass.

Then wet the whole window with warm water and a few drops of dish soap. A few drops is the whole recipe, for the same reason covered in the piece on cleaning windows without streaks. Dish soap is built to cling, and too much of it dries into a film of its own.

Work the brush in small circles rather than straight lines, because circles reach into a ripple from every side. Give the mortar joints a pass of their own. Then rinse from the top down, with a hose outside or a sponge and clean water inside. Rinsing matters more here than on flat glass, because soapy water left in the texture dries into the exact haze you were trying to remove.

Dry what you can reach with a microfiber towel folded to a point for the grooves. Glass block does not streak the way a flat pane does, so a little air drying does no harm.

What does not work, and what can do damage

A squeegee is not a weak choice here, it is the wrong tool. The rubber bridges the ripples and leaves a line of dirty water in every groove. A razor blade is worse. On flat glass a blade is a legitimate tool, but a molded surface gives the edge something to catch, and older block was often painted at some point, which a blade will take straight off.

Abrasive pads and scouring powders will dull the high spots over time, and that dulling does not come back. And if the mortar between the blocks is crumbling, or a joint has opened up, then cleaning is not the job in front of you. That is work for a mason rather than a window cleaner, and we would rather tell you so than brush over it.

What a clean glass block window actually looks like

This is worth knowing before you start. Glass block is obscure glass on purpose. It was made to let light through while breaking up the view, which is how it ended up in basements and bathrooms in the first place. Cleaning it makes it brighter. It does not make it clear, and nothing will.

Some of what looks like grime will not move either. Mortar haze from the original install, old paint and dirt pressed deep into the pattern all turn up on block in houses that have stood for most of a century, and St. Paul and Minneapolis are full of those. Brighter is the honest goal.

Do the outside before the hose goes away

Timing matters more for block than for the rest of your windows, because the outside face really wants a hose. Once the ground freezes and the spigot is shut off, washing a low window outside gets much harder, and snow tends to drift against basement glass and sit there until spring. Late fall is the last comfortable chance. If the glass is already cold, the piece on how cold is too cold to clean windows outside covers where the line is.

Glass block is one of the easier jobs to keep for yourself. It sits at ankle height, it needs a brush rather than special gear, and no ladder comes into it. Where a call makes sense is a whole house where the block gets done along with the rest of the windows, or block at the bottom of a deep well you would rather not climb into. We clean glass around St. Paul and the rest of the Twin Cities. There is a price at our quote page and open times at our booking page.

Want a Gleam Team pro to handle it?

We serve St. Paul, Minneapolis, and the Twin Cities suburbs. Quotes and consultations are free.

Or call (763) 237-4106

CallQuote for spring